All content © copyright DavesDrivers forums 2007-2014


Post Reply 
 
Thread Rating:
  • 0 Votes - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
SN9C325
11-30-2010, 11:59 PM
Post: #1
SN9C325
I tried to install the "official" SN9C325, the installer won't even open up!

Are there any alternative drivers? I've searched countless times too.

This my hardware ID:
USB\VID_0C45&PID_612A


This is the device id:
USB\VID_0C45&PID_612A\5&3714C0AC&0&8
Quote this message in a reply
12-01-2010, 12:08 AM
Post: #2
RE: SN9C325
just having a look over google with that device id string.
it may be the SN9C110 chipset inside that cam.
please try this set of drivers.

http://www.sonix.com.tw/sonix/download.do?d=5375,2

please do not email me, please use the forum to request driver support.
Visit this user's website Find all posts by this user
Quote this message in a reply
12-01-2010, 12:10 AM
Post: #3
RE: SN9C325
for info the last set of SN9C325 drivers that i know of come direct from sonix and they can be downloaded from here.
http://www.sonix.com.tw/sonix/download.do?d=2273,2

please do not email me, please use the forum to request driver support.
Visit this user's website Find all posts by this user
Quote this message in a reply
12-01-2010, 12:23 AM
Post: #4
RE: SN9C325
(12-01-2010 12:10 AM)davey6 Wrote:  for info the last set of SN9C325 drivers that i know of come direct from sonix and they can be downloaded from here.
http://www.sonix.com.tw/sonix/download.do?d=2273,2

It crashes.
Quote this message in a reply
12-01-2010, 12:30 AM
Post: #5
RE: SN9C325
what windows you trying to install this on ?

trying downloading that driver and i am going to check it on my system.
if i can unpack it enough and pull out the driver files for you i will.

please do not email me, please use the forum to request driver support.
Visit this user's website Find all posts by this user
Quote this message in a reply
12-01-2010, 12:32 AM
Post: #6
RE: SN9C325
Windows 7, I tried putting the setup in compatibility mode for different versions of older Windows.

This is the crash report:
Code:
Problem signature:
  Problem Event Name:    BEX
  Application Name:    sonix_sn9c325.exe
  Application Version:    12.0.0.49974
  Application Timestamp:    4474907b
  Fault Module Name:    StackHash_b69f
  Fault Module Version:    0.0.0.0
  Fault Module Timestamp:    00000000
  Exception Offset:    03204790
  Exception Code:    c0000005
  Exception Data:    00000008
  OS Version:    6.1.7600.2.0.0.256.1
  Locale ID:    1033
  Additional Information 1:    b69f
  Additional Information 2:    b69f1ff768e2ee076e3261a4c07eb8f0
  Additional Information 3:    f82c
  Additional Information 4:    f82cf87e64bf864edefb0b1840ef97dd

Read our privacy statement online:
  http://go.microsoft.com/fwlink/?linkid=104288&clcid=0x0409

If the online privacy statement is not available, please read our privacy statement offline:
  C:\Windows\system32\en-US\erofflps.txt
Quote this message in a reply
12-01-2010, 12:54 AM
Post: #7
RE: SN9C325
i just tryed the installer on windows 7 64 bit, it moans but installed.

if you go to the warning about m/s not testing the dver click continue anyway.

crashing maybe even be down to your firewall / anti-virus software stopping the driver from installing as it trying to get access to a port.
so if possible shut down your firewall, anti-virus only while your trying to get this cam installed.


i installed this and found the three basic files it install's in winodws so you can try it this way as well.
download the winrar file on this post.
unpack it to folder on your desktop.

plug the cam in and wait for windows to finish screwing about looking for a driver.
when its done that go in to device manager and look down the list for the problem cam.
right click your mouse on that and select update driver.
at this point don't let windows search online tell it you want to search.
click browse button and now browse to that unpacked files.
highlight one of the files and click next,
that will bypass the self install but it will also bypass the amcap program which does crash on windows 7
these three files are the basic cam driver.


Attached File(s)
.rar  SNP325.rar (Size: 79.27 KB / Downloads: 54)

please do not email me, please use the forum to request driver support.
Visit this user's website Find all posts by this user
Quote this message in a reply
12-01-2010, 01:05 AM
Post: #8
RE: SN9C325
I appreciate your efforts but I have another error now >.<.
When I try to install the drivers, it won't pick it up as in this:
[Image: 11090tw.png]
I also noticed there isn't a .ini file.
Quote this message in a reply
12-01-2010, 01:14 AM
Post: #9
RE: SN9C325
ok let me try again, but those three files are the only ones that installed in the system folder.
i will now take another look now and see if i missed anthing at all.

please do not email me, please use the forum to request driver support.
Visit this user's website Find all posts by this user
Quote this message in a reply
12-01-2010, 01:24 AM
Post: #10
RE: SN9C325
I truly am grateful for your help.
Quote this message in a reply
12-01-2010, 01:29 AM
Post: #11
RE: SN9C325
ok i think i found them all.

its too big for me to attach to the forum software i am going to upload it to site now and post back a few mins with a link for you to try.

please do not email me, please use the forum to request driver support.
Visit this user's website Find all posts by this user
Quote this message in a reply
12-01-2010, 01:35 AM
Post: #12
RE: SN9C325
ok thats done try this the same way load it from device manager
http://www.davesdriversfiles.com/memberu...n9c325.rar

please do not email me, please use the forum to request driver support.
Visit this user's website Find all posts by this user
Quote this message in a reply
12-01-2010, 01:40 AM
Post: #13
RE: SN9C325
Thanks so much!
It worked and it installed just fine, is there a way to check if my webcam works?Grin

Edit: I read of some your old posts and you said to test with msn. I did and it doesn't work :(.
Quote this message in a reply
12-01-2010, 01:51 AM
Post: #14
RE: SN9C325
if its installed and windows has named it it might have been blocked by the firewall

when in messenger run the webcam wizard, it should give you something, black , green , white screen

please do not email me, please use the forum to request driver support.
Visit this user's website Find all posts by this user
Quote this message in a reply
12-01-2010, 02:07 AM
Post: #15
RE: SN9C325
you can move the cam down one usb port now as well.
if the driver is installed windows will now auto find it and reload the driver.

if you do that please make sure no firewall is on not even windows firewall.

its just gone 2am i need some sleep, hoever if you still can't get a picture out of that cam try this.
take the back of the cam off and look at the chipset with your eyes just in case you have the wrong sonix chip.

you should see sonix on the chip and then its model number just as in this post.
http://www.davesdrivers.com/forum/showth...hp?tid=817

let me know what you find out and i will take a look when i get out of bed.

please do not email me, please use the forum to request driver support.
Visit this user's website Find all posts by this user
Quote this message in a reply
12-01-2010, 02:12 AM
Post: #16
RE: SN9C325
This is the image when I try to use:
[Image: muwumx.png]


The chip number says this exactly:
SN9C325AFG
Quote this message in a reply
12-01-2010, 10:59 AM
Post: #17
RE: SN9C325
going by that screen the driver install was blocked.

windows can not access the port the cam is sitting on.
it knows what the cam is now but can't access it, that warning about another program using the device may be down to a firewall blocking windows

you do have the correct set of drivers for that cam and i will search to see if i can find anything others on the net.

if possible try that cam on a different machine and see if it works might just be windows 7 being a pain but its best to check.

please do not email me, please use the forum to request driver support.
Visit this user's website Find all posts by this user
Quote this message in a reply
12-01-2010, 11:32 AM
Post: #18
RE: SN9C325
(12-01-2010 10:59 AM)davey6 Wrote:  going by that screen the driver install was blocked.

windows can not access the port the cam is sitting on.
it knows what the cam is now but can't access it, that warning about another program using the device may be down to a firewall blocking windows

you do have the correct set of drivers for that cam and i will search to see if i can find anything others on the net.

if possible try that cam on a different machine and see if it works might just be windows 7 being a pain but its best to check.

I also tried AMCap and another website called testmywebcam.com to no avail :(.
Quote this message in a reply
12-01-2010, 03:19 PM
Post: #19
RE: SN9C325
AMCap is dos based and is well known not to work too well with windows 7

do you have any third party firewall on that pc ?
just sitting here trying to figger out what is blocking windows from accessing that device.

please do not email me, please use the forum to request driver support.
Visit this user's website Find all posts by this user
Quote this message in a reply
12-01-2010, 09:01 PM
Post: #20
RE: SN9C325
(12-01-2010 03:19 PM)davey6 Wrote:  AMCap is dos based and is well known not to work too well with windows 7

do you have any third party firewall on that pc ?
just sitting here trying to figger out what is blocking windows from accessing that device.

None at all, just the default Windows Firewall.
This my security setup:
Eset Nod32
KeyScrambles (Anti-Keylogger that scrambles your keys)

That's it.
Quote this message in a reply
Post Reply 




All content © copyright DavesDrivers forums 2007-2014davesdrivers.com"